Design In: New Thermocouple Terminal Block - allowing your Control System to go the extra mile.

American Electrical's new line of DIN Rail mounted Thermocouple Terminal Blocks can allow your Control System to bring back T/C wire to enhance system accuracy and eliminate cold junctions.  Our new TCB-K (for type K Thermocouples) and TCB-J (type J) have an embedded female T/C connector that allows the user to "read" process temps at the Terminal Block - saving the Technician valuable time.   Call us at 804 379-2899 or visit us online at www.americanelectrical.com !

Wire Duct Cutter by American Electrical - fast and easy way to make precise cuts in your wire duct

See the new Wire Duct Cutter from American Electrical Inc. !!!  Fast, burr free and precise cuts!

Design In: New Interface Relay saves space on the DIN Rail, from American Electrical, Inc.

Now Design Engineers have a better, slimmer way to control systems in machinery and processes. Our new Interface Relays come in 115VAC/DC or 24 VAC/DC in a slim 6mm, DIN Rail mountable package.  There are two sets of contacts, 1 NO and 1 NC that can each carry 6A, for less than $20.00 804 379-2899 call us today or check out our website at www.americanelectrical.com

Design In: Engineer's Choice Award :: Terminal Blocks ... In a Box. Ready for your control circuit.

American Electrical brings you our new  Junction/Hookup Boxes that have the DIN Rail and Terminal Blocks already mounted in this IP 65, NEMA 4X J-Box.

Have a wire run you need to terminate and re-run or perhaps monitor a small I/O block? Are you looking for a way provide a parallel circuit to an existing design? Are you looking to control, automate or monitor a plant  or machine process?

Whatever your needs may be, we have 5, 10, 15 (35 amps) and 20 (26 amps) position feedthru terminations PRE INSTALLED for you in this high quality, gasketed, mountable NEMA 4X J-Box, saving time, space and $$ ! The terminals are spring loaded - open the clamp with a screwdriver, insert wire, remove screwdriver !  It's that simple!  Terminals are cUL Registered Call us today at 804 379-2899

Design In: D-Sub signal breakout module:: Now you can measure/monitor/roll conductors to your specification !

American Electrical's  D-Sub signal breakout modules allow the user to take a cable terminated with a #D-Sub (9, 15 or 25 pin) and convert it to discrete wires so that #measurement, monitoring, testing, control, troubleshooting or rolling conductors, etc. can be performed.  Call us at 804 379-2899 We also make 3 versions for  IDC connectors !

Follow us on Twitter @AmericanElecInc  and RETWEET please if this was helpful ! thanks!

Design In: Protect your People and your Equipment in wet environments with our new DIN Rail Mounted GFI Breaker

American Electrical's NEW * GFI * DIN Rail mounted #Circuit #Breaker is UL 1053 and UL 1077 rated - providing 22ma #ground #fault protection @ 240VAC - protecting Personnel and Property in a 26mm slim package saving valuable space along the #DIN Rail !  Call us today at 804 379-2899 ! #circuitprotection #GFCI #GFI

Design In: American Electrical's new Wire Stripper :: Engineered for your production floor

American Electrical, Inc.'c new CS 60 Wire Stripper strips insulation for 28-10 AWG conductors.  Stripping lengths up to 20mm can be set as well as the distance the insulation gets pulled back.  This machine weighs 21 pounds, portable to move about the factory floor, yet rugged in design so that it can take most any tough environment.  LCD display makes it easy to use and understand.  Call us today 804 379-2899 !!!